Pages: [1]   Go Down

Author Topic: Z3200 58:10 color sensor error persists after replacing color sensor  (Read 826 times)

plasakow

  • Full Member
  • ***
  • Offline Offline
  • Posts: 100

I started having color sensor/ESP errors before replacing the current carriage with a rebuilt unit from LP Computers. When the new carriage failed the ESP test, I asked LP to send a new ESP, which they did, and which I installed. I'm still getting 58:10s while trying to do a color calibration or profile.

Is there anything that could cause this besides the ESP itself?

Thanks.
Logged

kers

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 4622
    • Pieter Kers
Re: Z3200 58:10 color sensor error persists after replacing color sensor
« Reply #1 on: November 14, 2026, 10:53:37 am »

hello Plasakow,

I am having the same problem- did you find a solution?

I put in a sensor that works in an other z3200 so it should be fine, but still it says out of specs...

Logged

degrub

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 2577
Re: Z3200 58:10 color sensor error persists after replacing color sensor
« Reply #2 on: November 14, 2026, 11:11:16 am »

hello Plasakow,

I am having the same problem- did you find a solution?

I put in a sensor that works in an other z3200 so it should be fine, but still it says out of specs...

do you have a copy of the maintenance/diagnostic manual from HP ?
If not, search the threads from Sharadn . There is a link/copy in there from when we  were helping him troubleshoot.
Logged

plasakow

  • Full Member
  • ***
  • Offline Offline
  • Posts: 100
Re: Z3200 58:10 color sensor error persists after replacing color sensor
« Reply #3 on: November 14, 2026, 11:48:01 am »

hello Plasakow,

I am having the same problem- did you find a solution?

I put in a sensor that works in an other z3200 so it should be fine, but still it says out of specs...

If I recall correctly, with LPS's help I eventually decided it was a firmware thing. Or, in other words, I really don't know.  About a year ago I replaced both my printers with still-in-the-box 2300PSs. I'm going to run those until it no longer makes sense to. The main reason is that, for my use, aftermarket inks make sense. It saves me a ton of money.
Logged

kers

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 4622
    • Pieter Kers
Re: Z3200 58:10 color sensor error persists after replacing color sensor
« Reply #4 on: November 14, 2026, 12:36:56 pm »

hello, I just discovered that it is the door of the sensor that does not open...

I have replaced my old service tank with a new one from China - that will be the reason. (If I open the sensor manually ...well timed ... it just works...)

but that means i have to open the right side every time I calibrate.... (!)
I will look into it further, many Thanks to you both for the quick replies...

- as i see now thee is a little piece of metal missing in this new servicetank that takes care of opening the colorsensor, maybe i can put the one from my old tank in...
phew !   it seems you are never finished repairing! but at least i know now what the problem is.

even if you get the right service part by the numbers it is different...


« Last Edit: November 14, 2026, 01:21:57 pm by kers »
Logged

Kyle Jackson

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 538
    • Lone Leaf Photography
Re: Z3200 58:10 color sensor error persists after replacing color sensor
« Reply #5 on: November 15, 2026, 10:00:52 am »

The ESP diag test is a PITA! In my case the ESP itself was fine and all the issues were paper-related. It's possible you're encountering the same thing.

The Carriage Assembly diag test includes an ESP test. It doesn't tell you however that paper must be loaded for that part of the test (and unloaded for other parts)   :(  Without paper it will fail. And if you skip the ESP test step instead, the entire Carriage Assembly diag test fails. So it's bad test instructions, not hardware issues.

There is a separate ESP test, on the diag test menu as test #6 "SOL" (at least on my Z3200ps Rev B 24"). Do that one instead. This test actually prompts for paper. It can fail on matte paper (not bright/shiny enough I guess) so use a glossy/satin paper.

During that ESP / SOL test you can see the shutter door open and its lighting up the paper (see pics).

This should confirm if your ESP is ok.

All my 58:10 issues (during cal/profile scanning) were caused by paper curl..., or at least fixed by not using curled / end-of-roll paper. If I used less-curled paper, even by manually reverse rolling the leading edge of the roll before using it, it worked fine. Ditto for paper loading fails, like "paper edge not detected" etc. My Z3200 seems much more sensitive to paper issues than my Z3100 was. I could probably load dirty socks into my Z31 and it wouldn't care, but my Z32 is little prince fussy pants.  ::)

« Last Edit: November 15, 2026, 11:04:54 am by Kyle Jackson »
Logged

plasakow

  • Full Member
  • ***
  • Offline Offline
  • Posts: 100
Re: Z3200 58:10 color sensor error persists after replacing color sensor
« Reply #6 on: November 15, 2026, 03:08:37 pm »

hello, I just discovered that it is the door of the sensor that does not open....

As soon as you said this my memory came back. You're likely missing a tiny piece of plastic on the service station that opens the ESP door. It's called an actuator, and I went back and forth with LPS for months, and spent lots of money on unnecessary equipment replacements, until they did some research and discovered it exists. Before that, they simply didn't know about it and were not checking the rebuilt SSs they sold.

See https://www.lpscomputer.com/blogs/news/hp-designjet-z2100-z5200-z3100-z3200-error-58-10?srsltid=AYCX9vJGrlN-1huHXQl-VnzBN16Kz1bcOcMIlGjPWOMVJcgZ3p3KvhCE
Logged

kers

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 4622
    • Pieter Kers

As soon as you said this my memory came back. You're likely missing a tiny piece of plastic on the service station that opens the ESP door. It's called an actuator, and I went back and forth with LPS for months, and spent lots of money on unnecessary equipment replacements, until they did some research and discovered it exists. Before that, they simply didn't know about it and were not checking the rebuilt SSs they sold.

See https://www.lpscomputer.com/blogs/news/hp-designjet-z2100-z5200-z3100-z3200-error-58-10?srsltid=AYCX9vJGrlN-1huHXQl-VnzBN16Kz1bcOcMIlGjPWOMVJcgZ3p3KvhCE
yes , that is it... but it is metal...
apparently under the same HP code you can get different types of service stations. I bought it new in china for at some point the motors will stop working and plastic joints will break.
So be aware if you need one. the other functions seem to work well, we will see.

Logged

kers

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 4622
    • Pieter Kers

...
All my 58:10 issues (during cal/profile scanning) were caused by paper curl...

as I understand - the basic paper used for testing, checking and calibrating the printer is HP ID premium gloss paper.
and then as flat as possible for the last part of the roll is very curly.

I could have diagnosed my problem much  quicker if i had fully read the manual. it now truly gave me the answer: door of the sensor  did not open.


Logged

Kyle Jackson

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 538
    • Lone Leaf Photography

Hopefully you can attach the metal hook from your old service station onto your new one. Or maybe make a new hook somehow, it looks like a relatively simple part.
Logged

kers

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 4622
    • Pieter Kers

Hopefully you can attach the metal hook from your old service station onto your new one. Or maybe make a new hook somehow, it looks like a relatively simple part.
yes i have a look into it... i have two printers and can swap some parts - so at least one of them is running as it should.
I just switched the service tank and it seems to work
In countries where it is difficult to obtain spare parts people often buy two items.
Logged
Pages: [1]   Go Up