Gretag Macbeth/X-Rite i1 Pro Spectrophotometer (Rev. B) in fitted carrying case with accessories, all in as new condition. £280 + insured carriage at cost (UK Parcelforce 48 2-day service @ £19.28, or Royal Mail Special Delivery 1pm @ £26.60)
Purchased new in 2005 as the original Rev. A model, this was fully serviced and recertified by X-Rite in October 2007 following a lamp failure, which included an upgrade to the later Rev. B version. This has had only minimal use as a backup instrument since it was serviced and recalibrated, and passes all diagnostic tests. Please see the X-Rite diagnostics report below for operating times and other parameters.
Included is the i1 Pro with matching calibration plate, ambient light head, carrying case, cable, spot measurement adaptor, monitor adaptor and updated scanning ruler with backing plate and target holder.
Note, the i1 Pro still has the original serial number label on the bottom which identifies it as the Rev. A model, but the service upgrade to the Rev. B version is confirmed in the diagnostics report (see Instrument information)
i1Pro Tests
General Information
Date and Time: 06/03/2016 14:41:31
Application version: 4.1.2.290, 32-bit
SDK version i1Pro: 4.2.3.4987
SDK version i1iO: 2.2.3.4987
SDK version i1iSis: 2.0.0.4968
SDK version ColorMunki: 1.0.3.4630
SDK version i1Display2: X-Rite, Inc. SipCal Library Ver. 7.3.7 (32 bit)
Platform: Microsoft Windows 10, 64-bit
Open instrument
Connection: Successful
Open instrument: Successful
Instrument information
Instrument inspection: Successful
Serial number i1Pro: 118954
Type: i1Pro
Revision: B
Firmware version: 202
CPLD version: 2
Dark measurement count: 11214
Lamp burning time: 5453.1 seconds
Spot measurement count: 149
Scan measurement count: 1259
Factory calibration: 29/10/2007
Instrument Licenses
Measurement Modes: [Reflectance Spot, Reflectance Scan, Emission, Ambient Light Spot, Ambient Light Scan]
Licensed functionality: [Has Ambient Light, Spectral values, Tristimulus, Density]
Licensed Modules:
i1Match Module "Scanner": NOT licensed
i1Match Module "Monitor": NOT licensed
i1Match Module "Printer": NOT licensed
i1Match Module "Printer RGB only": NOT licensed
i1Match Module "Printer CMYK only": NOT licensed
i1Match Module "Beamer": NOT licensed
i1Match Module "Printer Easy RGB": NOT licensed
i1Match Module "Printer Easy CMYK": NOT licensed
i1Match Module "Digicam": NOT licensed
i1Match Module "Editor": NOT licensed
i1Profiler Module "Display Profiling": NOT licensed
i1Profiler Module "RGB Printer Profiling": NOT licensed
i1Profiler Module "CMYK Printer Profiling": NOT licensed
i1Profiler Module "Printer QA": NOT licensed
i1Profiler Module "Advanced-Mode": NOT licensed
i1Profiler Module "Projector": NOT licensed
Button test
Button: Successful
Emission test
Emission calibration: Successful
Prepare the instrument for emission measurement
White measurement: Successful
Gray measurement: Successful
Black measurement: Successful
Red measurement: Successful
Green measurement: Successful
Blue measurement: Successful
Emission: Successful
Button test
Button: Successful
Noise Tests
Dark measurement: Successful
Noise measurements: Successful
Noise result: Successful
Reflectance test
Reflectance Spot calibration: Successful
Reflectance Spot measurement 1: Successful
Reflectance Spot measurement 2: Successful
Reflectance Spot measurement 3: Successful
Reflectance Spot measurement 4: Successful
Reflectance Spot measurement 5: Successful
Reflectance Spot measurement 6: Successful
Reflectance Spot measurement 7: Successful
Reflectance Spot measurement 8: Successful
Reflectance Spot measurement 9: Successful
Reflectance Spot measurement 10: Successful
Lamp test: Successful
Reflectance drift test: Successful
Reflectance Scan calibration: Successful
*** PASS ***
