Luminous Landscape Forum
Equipment & Techniques => Cameras, Lenses and Shooting gear => Topic started by: Michael Perlmutter on November 14, 2011, 05:54:51 am
-
I am a professional architectural photographer investigating the transition from LF to digital photography. I have a long list of questions about this, but will just stay focused on one issue here: lenses. I am looking into DSLR, since MF seems way too out of the ballpark cost-wise.
I have a Canon 5d MkII, and would be interested to hear from other architectural photographers who have already made the digital transition: Which lenses to use? I am starting from scratch here on this, since I only have the first TS-E 24mm, which I know needs to be upgraded. I am used to LF Schneiders and Rodenstocks, and would like to hold that standard, at least as close as possible.
As I see it, after checking around, there are basically 2 viable options: Either get the whole set of Canon TS-E lenses plus a 1.4x extender, or get the Canon TS-E 17mm and 24mm II, plus a Mirex TS lens adaptor with a set of Mamiya N lenses (35mm, 45mm, 55mm, 80mm M, 120mm M, 150mm). Any feedback on this? The issues are sharpness, lens distortion, CA, etc, but also ease of use (important when working quickly under pressure). The extender will degrade sharpness, but enough to think twice about going that route? Schneider's TS and shift-only lenses seem too problematic, from what I have read, and don't seem to be a good solution for digital architectural photography.
Though cost is always a concern, I need to stay focused on the best options, since the cost differences between going all Canon or Canon plus Mamiya are not so far apart (compared to the cost difference between choosing DSLR or MF).
A related question concerns how to deal with correcting lens distortion. Lens correction software, like PT-Lens or the lens correction tool in Lightroom, has various correction profiles for a range of camera-lens combinations, but the old Mamiya lenses are not there (no lens data is recorded for each shot), and using shift complicates things for both the Canon and Mamiya lenses. PT-Lens has a rather cumbersome method for correcting shifted lenses, where among other things one needs to note the amount of shift for each shot taken. Anyway, how great an issue is this with the different lenses in question, and how are you dealing with it?
-
do a search, there is at least one extensive thread on the 5D2 for arch
i heartily agree with using a gimbal for pano
-
I shoot with Nikon but I think the essential focal lengths to have in perspective control lenses would be 17mm, 24mm, and 35ishmm (using the 1.4x extender). I have tried them and both the Canon 17mm and 24mm (version 2) have very little distortion and what little distortion there is would be easy to correct in Photoshop. I use a 24mm PC and a 24-70mm zoom often. I have used the 45mm PC a few times but always wished for something a smidge wider (like a 35mm PC). Every so often I will use a 70-200mm zoom as well. The vast majority of my interior photographs are taken between 35mm and 70mm but as I shoot more architecture focused projects I find myself needing to shoot a bit wider.
I don't see the advantage to using Mamiya lenses on your Canon and would think that image quality would suffer somewhat trying to use larger format lenses on a 35mm sensor. I'd stick to Canon mount lenses.
"The 24TSE stitch gives a more natural wide look without the stretched distortion common with wide 35mm camera lenses in single frame final images."
Not sure what you mean by this statement. Images with the same field of view taken from the same location will have the same amount of stretched distortion regardless of the amount of stitched frames used to create the image.
-
Yes John, Stockholm, Sweden. No problem about renting lenses here, and I have indeed rented the 17 TS-E and 24 II TS-E a few times, so I do know something about how good they are. Shooting a lot of interiors as I do, especially domestic spaces, the 17mm would have a place, but yes you are right, it must be used judiciously.
It is true for me as well that the 45 TSE and 90 TSE would be used a lot less in architectural work. But I also photograph a fair amount of architecturally integrated art works, so being able to zoom in a bit more is often needed for that, while keeping verticals parallel. On the other hand there is a huge need for a 35mm shift lens for exteriors, and since such a lens doesn't exist, I am searching for a good solution to this. Hence my question about the Mamiya lenses with TS adapter, which I have read about in other forums (See for example www.fredmiranda.com/forum/topic/882423).
As for stitching, well, I definitely see the benefit of using the Canon this way, and have done some of that now and again pretty successfully. (John, what is "5.5" when you say that PS CS5 and 5.5 can do all the stitching work?) I completely agree about wanting to get away from the 3x2 vertical look as well. But after so many years of composing images on the ground glass of the LF camera, where I can see and judge the entire image as I intend it to be, I find it difficult to pre-visualize the result of a stitch when trying to compose with the Canon. I mean, since I can't see the whole stitched-together composition on the rear screen, I have to put it together in my mind, and for me this doesn't come so naturally. It still feels like shooting a stitch is a little like taking a hail-mary shot, hoping and expecting the composition will come out good, but I can't really be sure. I don't honestly know if I could shoot every image that way...but perhaps one learns eventually?
Would it be strange to do the opposite, and instead of stitching you just crop a single-frame to get a 4x3 format, then do a bit of interpolation as needed to get the minimum file size you need?
And to throw another wrench into the works, if you are shooting hdr, what does the workflow look like when you are stitching: do you first apply the hdr software to the many exposures of the 3 different images of a stitch, then do the stitch afterwards? Or is it the other way around, first stitching each exposure, then applying the hdr? Either way, seems like a fair amount of prep work before you can even judge if the image is to your liking. If all your images in a set are shot for both stitching and hdr, doesn't it get to be a bit too much?
Concerning the Induro GHB2: this is marketed as a head for users of very long and heavy telephoto lenses. What makes it special for stitching/panos as well, compared to say the Manfrotto 405, which I have been using over the last 6 months or so? I am not quite getting it.
-
I'm very happy with my current equipment doing interior and architecture photography.
My equipment:
5DII
TS17
TC1.4II
TS24 buying in xmas. Sold my old 24 and my old 45 Ts's. Meanwhile using 17-40 and 70-200 when I need them. Not the same, of course.
The TS17 with TC1.4II (fl=24mm) is way sharper and more corrected in every department than the old 24TS
I'm waiting for the new TS45 and the new TS90 to show up and get them (one at the time)
Unbelievable easy stitching makes the 5DII/TS combo the digital medium format of the not rich. Especially easy with a sliding ruler or a collar. If you print big.
Eduardo
-
There is allot of info related to this on my blog. Pardon me for not wanting to repeat it here-no time.
-
The 24TSE stitch gives a more natural wide look without the stretched distortion common with wide 35mm camera lenses in single frame final images.
2 shifted vertical images with a 24mm tse stitched together will produce the same image as one horizontal taken with the 17mm tse.
The stitch will have a higher resolution of course, but perspective distortion will be exactly the same.
The level of perspective distortion is defined by the distance to the subject, not the lens you're using.
-
I'm also using the 17mm tse, the 24mm tse II, and a 1.4 extender with the 24.
I only use the 17mm when I have to, and then it really is a lifesaver.
For my taste too the 45mm ts is not good enough, so I'm using the 24-70 instead. The 17-40 has too much barrel distortion.
For larger projects I could really use a 45mm tse though. I had high hopes for the Schneider 50mm, but it seems we'll have to wait for a new Canon design.
And a 35mm tse would be great as well of course...
-
The most cost effective way is of course to just use what you have and stitch into panorama images. But that will rob you of energy and creativity during shooting, compared to getting both 17mm TSE and the new 24mm TSE II.
I would prefer getting the TSE lenses, let's you see the results right away so that you can make angle or focus adjustments on the spot (kind of hard to judge if you have 4-12 images of the scene you plan to stitch).
-
Pretty much ditto what John S said.
I shoot 5DmII, 24TSmII, and 1.4x extender -- LOVE it. I am actually looking at a Zork adaptor and a Mamiya 45mm to gain the next step in PC focal length: I do a fair amount of detail shots and it would be useful often enough to justify the ~$600 or so of cost, I think.
Flat stitching with the 24TS couldn't be easier.
-
This is true. I find stitching gets in the way of the creative process. Exact framing is impossible unless you back up a little and then you crop at will in post.
I found a way to overcome this to a certain extent. If I'm stitching 2 frames with a 24TS, I know I'm going to end with a perspective and framing if done with a 17mm. So, first I do the framing (sensor in horizontal) with the 17mm on tripod then I switch to the 24TS and do the shifts (sensor in vertical).
If stitching with 90TS final image is like 64mm lens.
If stitching with 45TS final image is like 32mm lens.
If stitching with 24TS final image is like 17mm lens.
If stitching with 17TS final image is like 12mm lens.
Notes:
Framing is 2:3 ratio. Final image is 3:4 ratio. So you end up with an image with a shorter x axis but a longer y axis. Taking notes helps a lot here.
An L bracket helps to maintain the same location of the lens in respect to your prior framing.
One or two zooms come very handy to accomplish the desired framing. Of course, fixed prime lenses seem at first to be first choice but not really. Primes often differ considerably from the nominal FL. Use a zoom lens and compare to the stitched image. Take notes and adjust zooming position.
Anyway, if it happens that you own these 8 primes, then you are a very lucky photographer.
If you encounter parallax errors that software can't fix, then you need a slide ruler or a collar. Because it happens once in a while.
There's a way to stitch with TS glass and able to maintain the same ratio of 2:3 both in vertical and horizontal, but that's story for other post. If someone is interested, please let me know.
Eduardo
The most cost effective way is of course to just use what you have and stitch into panorama images. But that will rob you of energy and creativity during shooting, compared to getting both 17mm TSE and the new 24mm TSE II.
I would prefer getting the TSE lenses, let's you see the results right away so that you can make angle or focus adjustments on the spot (kind of hard to judge if you have 4-12 images of the scene you plan to stitch).
-
@ scott
don´t go the mamiya-way. i work with zoerk-panorama-adapter and pentax 70mm. 55mm is also very good as i heard. i had a pentax 35mm. it´s ok but not as brilliant as TS-E II 24.
what i´m looking for is a L-bracket. any advice?
bernhard
-
There's a way to stitch with TS glass and able to maintain the same ratio of 2:3 both in vertical and horizontal, but that's story for other post. If someone is interested, please let me know.
Eduardo
I'm curious about your approach to this.
-
Hi Kirk, my approach goes like this:
Instead of shifting left to right or up and down, I turn the lens to a position that the shift movements happen at 45 degrees. It takes 4 different shots shifted towards the corners of this exploded rectangle. In my case, I've found out that the the neutral shot at center position is not needed because all the other 4 "cornered" shots cover easily the whole center area. Nevertheless, I usually shoot in the neutral position first. Photomerge can do the stitch with or without it.
Canon TS glass have 2 detents at 30 degrees apart. In order to shift at 45 degrees you have to position the lens between the 2 detents. If you are careful positioning the lens it is always accurate enough for a good stitch. Maybe a mark can be painted at each of the 2 positions but I think it would be a nightmare finding the exact positions. Do Canon know about this? After Photomerge, you can see in your canvas how much your were off the 45 degree targeted shifting. Actually rarely they match perfectly between the 2 axis but I've seen this doesn't preclude the process.
The technique is the same for both vertical or horizontal stitches.
The best part of this more complicated approach is that you end up with a bigger file than doing it the "traditional" way. As much as 14%.
The other good part is that this technique maintains the same ratio, allowing exact visualization of your final picture by composing first with the wider corresponding lens.
The bad is that if you encounter parallax errors, the ruler doesn't doesn't work here. For this you need a collar. (Stefan, you owe me :D)
Best
Eduardo
I'm curious about your approach to this.
-
Yes that is what I do to. I thought maybe you had a different approach, but I have never encountered parallax errors that CS5 couldn't easily resolve.
-
Several methods of stitching are described in this thread. For those of you photographing this way, are you basically doing it for every shot? I am getting the sense that serious architectural photography on dslr almost requires this way of working ....?
-
FWIW, I have been a "serious" AP since 1978, and no I don't do it on every shot. I do it on shots that demand a different aspect ratio (I don't want to crop to a smaller file size), images that need a wider view and images that are going to be used very large. For 25 years I used 4x5 exclusively, but well before switching to digital I realized that 4x5 was overkill since 99% of my shots were never used above 8x10. So in my last years of film I switched to 6x9 roll film.
If I needed large files on every shot I would go to MF like an Arca technical camera and at least a P45+ back. BUT I have never had complaints about small file sizes. I've only had complaints about files being to large (seriously!) :).
-
No, not at all. Nowadays I rarely do stitches. Since the 5D2 with Canon latest wide-angles plus careful technique at optimal settings, I can go easily to 16X24". A little Genuine Fractals and I'm at 24X36" prints that would make green with envy any 6X9 drum scanned transparency (my personal reference). My 70-200 F4.0 IS copy is outstanding too. I can't hardly wait for the new iterations of the 90TS and 45TS.
My years of heavy stitching were when I was stuck with APS Canons (10D and 20D). Since the 5D my stitching needs decreased considerably.
Eduardo
Several methods of stitching are described in this thread. For those of you photographing this way, are you basically doing it for every shot? I am getting the sense that serious architectural photography on dslr almost requires this way of working ....?
-
Ok, just trying to think it through, and I know everyone's needs are different – I am accustomed to delivering file sizes that are suitable for magazine publication: 300 ppi, 6000 px (approx. 20") in the longest dimension for horizontal shots; 5000 px (approx. 17") in the longest dimension for vertical shots. Vertical shots for a full page with bleed normally need to be at a 3:4 ratio; while horizontal shots for a full 2-page spread (or for half-page) are usually around 2:3. Sometimes, however, I will want to do horizontals at 3:4 instead, for consistency with the verticals. For me it is very rare that I would need to deliver anything larger than these sizes.
The Canon 5d2 produces an uncropped 2:3 image that is 5616 px in the longest dimension (at 300 ppi). When cropped to 3:4, this longest dimension is reduced to 4992 px. For horizontal images, to get from say 5500 px (allowing for a little cropping) to 6000 px requires a 9% enlargement if I want 2:3; to get from say 4900 px to 6000 px requires a 22.5% enlargement if I want 3:4. For vertical images at 3:4, a cropped single frame would require an enlargement from say 4900 px to 5000 px, or 2%.
So what I wonder is: what is acceptable and what is not when it comes to cropping a single frame and then enlarging? In all the cases above I would need to enlarge. I could imagine that 2% and 9% should be ok (with no stitching required), and 22.5% might be ok too, but maybe not? Should one use Genuine Fractals or Alien Skins as a standard part of a workflow for the larger enlargements? Or is it better to plan on stitching all horizontal shots intended for a 3:4 ratio?
-
I think you could double the pixels in a properly focused/exposed 5DmkII file and not notice much of a difference, especially when it's offset printed in a magazine. 25% would be no problem for Genuine Fractals or AlienSkin or even Photoshop.
I've only stitched a handful of times and it was really to get an absurdly wide angle. Like others here I would prefer to compose as a single shot.
-
Check out the Horseman LD system that basically turns a Canon/Nikon body/lens combination into a view camera. I've seen one of these in the flesh and must say it is a compelling alternative to a TS.
http://www.komamura.co.jp/e/digital/LD.html
-
@ scott
don´t go the mamiya-way. i work with zoerk-panorama-adapter and pentax 70mm. 55mm is also very good as i heard. i had a pentax 35mm. it´s ok but not as brilliant as TS-E II 24.
what i´m looking for is a L-bracket. any advice?
bernhard
exactly.
i use 17 + 24tse II with 1,4 extender. also zoerk with pentax 45/55/75mm.
i have the 45tse too ( i hate it ) , the pentax 45 is better, although not as good as the excellent 55 and 75mm.
have the pentax35fa too, but canon 24tse with 1,4 extender is better.
-
Check out the Horseman LD system that basically turns a Canon/Nikon body/lens combination into a view camera. I've seen one of these in the flesh and must say it is a compelling alternative to a TS.
http://www.komamura.co.jp/e/digital/LD.html
ANyone used one of these? It does look interesting!
-
Very helpful and informative replies, thanks! Two related questions about lenses for shooting architecture and interiors:
Which aperture, f/11 or f/16? My heart says 16 (DOP) but my brain says 11 (diffraction). :)
Are UV/skylight filters needed with 35mm lenses? Never used them with LF.
-
Hi, I am brand new to this forum so apologies if this is a very basic newbie question. I came across this thread by wondering if you were able to use either the Canon 17mm and 24mm TS-E with a 1.4x extender..
Basically, I can only afford one lens at the moment, so figure I have two options..
a) Buy the 17mm TS-E and then use the 1.4x extender to get roughly a 24mm TS-E equivalent
b) Buy the 24mm TS-E and use a Pano head for stitching for the rarer times I would need such a wide field of view.. Then also use the 1.4x Extender to get a 33.6mm TS-E..
The second option is definitely my preferred I think..
With the Stitching/Pano head, the query that I was hoping someone may be able to answer relates below
Was just wondering if you are using Canon TS-E lenses, whether using a front rise/fall effects the nodal point of a lens and therefore create issues when trying to stitch images together?
For example, if I was doing a 2-3 pano stitch and wanted to use front rise to keep verticals straight for architecture (keeping the front rise in the same position for each of the shots) would this work? Or does the nodal point vary as soon as you introduce any front rise/fall?
I know that by introducing tilt that this alters the nodal point and you would effectively have to realign your Pano head as soon as you introduce any tilt (obviously completely unsuitable for field work) but was just wondering if this also applies for rise/fall?
As I see it, my option for stitching for architecture would be extremely limited if I cannot apply front rise to the stitched images (can live without tilt )
Hope this is clear :)
Thanks so much!
Look forward to hearing from you guys and hoping someone can resolve this issue..
-
b) Buy the 24mm TS-E and use a Pano head for stitching for the rarer times I would need such a wide field of view..
Hi,
That is what I do. Shooting with the 24mm will also give you (even) higher resolution than with the 17mm, due to higher magnification. I stitch to make up for any lack of FOV.
Then also use the 1.4x Extender to get a 33.6mm TS-E..
I haven't tried that myself (because I also have the TS-E 45mm), but people have reported that that is a usable solution. Of course, when you stitch you can also use a 50mm lens or longer use a proportionally narrower aperture (recover diffraction losses by deconvolution sharpening), and down-sample the result if necessary to get practically the same DOF and resolution.
Was just wondering if you are using Canon TS-E lenses, whether using a front rise/fall effects the nodal point of a lens and therefore create issues when trying to stitch images together?
Yes, any movement of the entrance pupil of the lens can cause issues, mostly when doing multi-row stitching, especially in the foreground features. A good Pano stitching software can offset most of that.
There are differences between simple shifted panos which just use the larger image circle of the TS lens, and rotational panos.
Cheers,
Bart
-
Hi, Thanks so much for the reply, is greatly appreciated!
Just a really quick one, so are most people stitching by using the larger circle of the 24mm TS-E to create a F.O.V close to 17mm or are people using dedicated Pano heads? I am a little confused ???
If they are using just the larger image circle approach, I imagine the resulting image might say, have a lot of unwanted foreground and then need to be copped in post anyway? Or am I missing something here?
Ok, Thanks again, is really helpful!
-
i use the nikon 24, 45 and 85 pce's.
if i'm stiching i find that dropping a linhof multiviewfinder on the hotshoe works well to visualise the shot. you have to 'calibrate' it a bit first to the lenses but once you get it properly marked it works well and using the 24 shifted means i don't miss an ultra wide...
-
Hi, Thanks so much for the reply, is greatly appreciated!
Just a really quick one, so are most people stitching by using the larger circle of the 24mm TS-E to create a F.O.V close to 17mm or are people using dedicated Pano heads? I am a little confused ???
If they are using just the larger image circle approach, I imagine the resulting image might say, have a lot of unwanted foreground and then need to be copped in post anyway? Or am I missing something here?
Hi,
I only stitch by using the larger image circle on rare occasions, when I need to travel light, or when the lower edge quality is not an objection (e.g. because the final result will be down-sampled). It's not mandatory to cover the entire image circle, only the relevant bits. With foreground detail, it also requires repositioning both the lens entrance pupil and the camera body in opposite directions, to keep the entrance pupil stationary. That can be hard with multirow stitches.
But when I have a choice, I prefer to do rotated pano stitching, as it always uses more of the center of the image circle, even when I combine it with tilt. Tilt often allows the use of relatively wider apertures, giving less diffraction and shorter shutter speeds.
On a rotation stitched pano, rise and fall are a simple operation of cropping a different part of the stitched result, without affecting the keystoning which can be perfectly corrected for, or slightly under-corrected if that looks better. It's usually easier to correct for keystoning in a Pano than it is in-camera, especially with wide angle lenses.
Cheers,
Bart