Pages: [1]   Go Down

Author Topic: HP APS profiles bad  (Read 1367 times)

dandeliondigital

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 262
    • http://www.dandeliondigital.com
HP APS profiles bad
« on: August 29, 2011, 03:12:38 pm »

Hi all,
I've been using my HP APS to profile our collection of studio monitors , and I just started doing a new set of profiles throughout the studio.

The profiles have a distinctly "green tint" and do not look normal at all. In the past, this wasn't the case. Of course, system software changes, and so does the HP APS which is now v1.41 for Apple Mac. I did get a profile on one iMac that came out looking right (usual), but 4 other monitors have a distinctly green tint to them.

I tried going onto the HP website, and all I can say is why not parachute yourself into Afghanistan for a similar experience?

Could my puck be bad? Are there any ways to test a puck's integrity?

I'm out of warranty and cannot talk to any tech from HP.

Anyone have any ideas?

Any suggestions would be appreciated.

Thanks, and so long for now, TOM
Logged

Ernst Dinkla

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 4005
Re: HP APS profiles bad
« Reply #1 on: August 29, 2011, 04:29:35 pm »

Copy of the HP list reply:

I have not seen an issue like that with two APS pucks and they both give
similar results. On Windows though. Right now I use them with
ArgyllCMS/DispcalGui + a correction matrix made with an i1 Pro which
improves at ;least the wide gamut monitor control. There is a choice in
the main APS window where you can select what ICC version (2 or 4) you
want to create. It might make the difference in Leopard OSses if you
stay with version 2 profiles.

If not you could try Dispcalgui with the HP branded i1Display II from
the APS package. You would need the ArgyllCMS modules and use the Argyll
driver for the puck. If the puck has problems it should show similar
problems with that software.


met vriendelijke groeten, Ernst

Try: http://groups.yahoo.com/group/Wide_Inkjet_Printers/
Logged

Pat Herold

  • Full Member
  • ***
  • Offline Offline
  • Posts: 161
Re: HP APS profiles bad
« Reply #2 on: August 29, 2011, 08:50:23 pm »

The APS puck is a re-branded X-Rite i1D2.  So you might get some useful feedback on it by running it through X-Rite's i1Diagnostic app. (You'll have to try it to see if it's compatible.)   This is a free utility that runs the puck through its paces, gives some raw numbers and give you a pass or fail on the instrument.  It is not as if you can totally depend on its conclusion, but it's a useful piece of information.
http://www.xrite.com/product_overview.aspx?ID=766&Action=support&SoftwareID=506
Logged
-Patrick Herold
  Tech Support,  chromix.com

dandeliondigital

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 262
    • http://www.dandeliondigital.com
Re: HP APS profiles bad
« Reply #3 on: August 29, 2011, 10:19:01 pm »

Hello,
Thanks so much for the link to the APS puck testing software. "i1Diagnostics 2.5.1" works, and my device passes all the tests! I'm stumped as to why this is behaving as it does. This Greenish Tint is just not right.

All the LCD screens I am testing are very old, and so far the youngest LCD screen is the only one giving me a profile that looks right.

During the APS profiling, 10 patches into the profiling (Create Monitor Profile "Optimizing"), the entire screen including the screen elements of the software (an oblong navigation blob with Home & the L & R arrows that is sorta shiny silver) picks up a definite greenish tinge.

I did an experiment and before profiling I used Apple's Display Calibrator Assistant to set the White point to D50, & Gamma to 2.2, and then when I ran the APS profiling the "greenish tint" was less than before, but is still evident.

I will play with all this later, but I thank you for helping me verify that the puck is not damaged.

Any other tips, tricks, comments or opinions are welcome.

So long for now, TOM

Logged

dandeliondigital

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 262
    • http://www.dandeliondigital.com
Re: HP APS profiles bad
« Reply #4 on: August 30, 2011, 08:15:08 am »

Hi Ernst,
Thanks for the hlep.

I am using v2 profiling. I was able to verify that the puck is OK.

I am wondering if I need to profile in safe boot mode? Seems to be something going on at a different level. Back in the days of Classic, I remember fixing odd issues by running a "clean system" without extensions.

Today, I think I will create a new administrator user and try profiling again.

So long for now, TOM
Logged
Pages: [1]   Go Up